曳引机装配流水线设备先进 新型无齿轮曳引机装配线生产厂家
创丰曳引机装配生产线、曳引机装配流水线的分类（按减速的方式来分）
1、有齿轮曳引机：拖动装置的动力，通过中间减速器传递到曳引轮上的曳引机，其中的减速箱通常采用蜗轮蜗杆传动（也有用斜齿轮传动），这种曳引机用的电动机有交流的，也有直流的，一般用于低速电梯上。曳引比通常为35：2。如果曳引机的电动机动力是通过减速箱传到曳引轮上的，称为有齿轮曳引机，一般用于2．5m/s以下的低中速电梯。
2、无齿轮曳引机：拖动装置的动力，不用中间的减速器而是直接传递到曳引轮上的曳引机。以前这种曳引机大多是直流电动机为动力，现在国内已经研发出来有自主知识产权的交流永磁同步无齿轮曳引机。曳引比通常是2：1和1：1。载重320kg～2000kg，梯速0.3m/s～4.00m/s。若电动机的动力不通过减速箱而直接传动到曳引轮上则称为无齿轮曳引机，一般用于2．5m/s以上的高速电梯和超高速电梯。
3、柔性传动机构曳引机，使用时再套在电机轴上。
曳引机生产线保养得好不仅仅能延长设备的使用寿命，还能使得设备的使用更。那么如何对曳引机生产流水线进行保养呢？创丰来告诉你！
1、机器在安装、拆卸和调整回转机构时，要注意保证非标自动化设备在初次对中心线与齿轮中心线平行，要适合的角度对好，有效保证机器在运转中做好。
2、我们的设备要经常检查各零件的保养和连接情况，如有松动应予拧紧。机体连接螺栓应在机体受压时检查松紧度所有连接稍轴都必须有开口销，并需张开充分。把主要的部件慢慢的平稳。
3、经常更换易磨损的零部件，如果有故障我们需要排除故障后再继续运行，电机轴承润滑要良好。经常检查所有的电线、电缆有无损伤。要及时的包扎和更换以损伤的部分。有效的延长机器保养。
组织曳引机装配生产线进行流水生产必须具备以下条件：
1、产品结构和工艺相对稳定，而且是长期大量需要的产品。
2、工艺过程能够划分为简单的工序，又能根据工序同期化的要求把某些工序适当合并和分解，各工序的单件时间不宜相差过大。
3、制品的产量足够大，单位制品的劳动量也较大，以保证流水线各工作地有足够的负荷。
4、原材料、协作件必须是标准的、规格化的，并能按时供应。
5、要有安装流水线的条件。
具备了上述条件，并通过技术经济的论证或可行性研究，作出决策。决定采用曳引机装配生产线进行流水生产方式后，就可以进行流水线的具体组织设计。
产品英文详情介绍
hoisting machine line-art new gearless machine manufacturers assembly line chuangfeng hoisting machine assembly line, assembly line classification of the hoisting machine (the deceleration manner minutes) 1, a gear hoisting machine: actuator the power is transmitted through the intermediate gear unit to the traction sheave of the hoisting machine, wherein the gearbox usually worm gear (helical gear is also useful), the hoisting machine motor is ac, dc also , generally used for low-speed elevator. traction ratio is generally 35: 2. if the hoisting machine motor power is transmitted through the gearbox of the traction sheave hoisting machine is called a gear generally used 2.5m / s or less in a low-speed elevator. 2, gearless traction machine: the drag power device, but without intermediate reduction gear is transmitted directly to the traction sheave of the hoisting machine. most of this before hoisting machine is powered by a dc motor, and now the country has developed with independent intellectual property rights of ac permanent magnet synchronous gearless traction machine. traction ratio is typically 2: 1 and 1: 1. load 320kg ~ 2000kg, elevator speed 0.3m / s ~ 4.00m / s. if the power of the motor without passing through the gear box directly to the drive sheave is called gearless machine generally used for more than 2.5m / s high-speed elevators and super high-speed elevators. 3, the flexible transmission mechanism of the hoisting machine, and then used when the motor shaft sleeve. hoist line not well maintained can extend equipment life, but also the use of such devices more. so how to carry out maintenance on the tractor production line it chong fung to tell you! 1, during machine installation, removal and adjustment of the turning mechanism, be taken to ensure non-standard automation equipment and the gear center line parallel to the centerline of the first time, to the appropriate angle for good, effective in operation to ensure that the machine check. 2, our device should always check the maintenance of the parts and connections, if loose should be tightened. body connecting bolt check the tightness of all connections must have an opening slightly shaft pin body when pressed, and the need to fully open. the main stationary member slowly. 3, regular replacement of wear parts, if there is a fault troubleshooting and then we need to continue to run the motor bearing lubrication to be good. always check all the wires, cables for damage. to timely dressing and replacement part to injury. effectively extend the machine maintenance. tissue hoisting machine assembly line production line must meet the following conditions: 1, the product structure and process is relatively stable, but large quantities need. 2, the process can be divided into a simple process, but according to the requirements of the procedure synchronization suitably combined and some decomposition step, a single piece of time difference in each step should not be too large. 3, the yield of products is sufficiently large amount of labor is also larger article units, to ensure that the pipeline has sufficient working load. 4, raw, collaborative pieces must be a standard, normalized, and can supply on time. 5, the condition of the pipeline must be installed. have these conditions, and by demonstrating the technical and economic feasibility study or make decisions. after the hoisting machine decided water production assembly line manner, tissue can be specifically designed pipeline.
温岭市创丰自动化设备有限公司
18516036306
